Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

  1. #11
    Top Contributor
    Join Date
    Oct 2010
    Location
    BD
    Posts
    2,720
    Thanks
    2
    Thanked 66 Times in 49 Posts

    answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

    x10i unlock x10i unlocked with usb cable on software 2.1.


    log

    SE - tool 1.8.2
    Selected model: Xperia™ X10 (X10)
    Selected operation: Unlock
    Selected interface: USB (EROM)
    Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 1-29-2010)
    Checking ADB drivers status...OK
    Remove battery, wait a few seconds and insert it back
    Plug USB cable holding "Back" button
    Connected to USB2
    You can now release the keys and allow the process to run. Do not disconnect the phone
    Device identification...OK
    Chip:QSD8250 Model:X10i IMEI:35941903-304723-3 AID:0001 Color:RED
    DEVICE_ID: B83E644CBDA932AC81AA99C3013E07977C97957F
    EROM: 1226-2253 R8A013
    Uploading logic QSD8250:
    Sending LoaderLIVE...OK
    Detecting flash type...OK
    ID: 2CB3 (Micron)
    Chip: Micron 8192 Mbit NAND (large page) x16
    Logical address: 0x08000000
    Size: 1056 Mb
    OTP: LOCKED
    Reading TA security data...OK
    Opening TA...OK
    Reading SIMLock data...OK
    Original HwConf certificate detected
    Processing SIMLock signature...OK
    Opening TA...OK
    Writing SIMLock data...OK
    Disconnect USB cable, power on the phone and boot Android OS
    Enable USB Debug in Applications menu, make sure ADB drivers installed. Connect USB cable
    Starting ADB server...OK
    Waiting for CB511HB9WW...OK
    Disabling security...OK
    Waiting for CB511HB9WW...OK
    Installing required module...OK
    Writing S1boot image...OK
    Rebooting device...OK
    Operation completed successfully. You can disconnect the phone now
    FINISHED [143sec]

  2. #12
    Top Contributor
    Join Date
    Oct 2010
    Location
    BD
    Posts
    2,720
    Thanks
    2
    Thanked 66 Times in 49 Posts

    answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

    4SE - tool 1.8.2
    Selected model: Xperia™ X8 (E15)
    Selected operation: Unlock
    Selected interface: USB (EROM)
    Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 5-4-2010)
    Checking ADB drivers status...OK
    Remove battery, wait a few seconds and insert it back
    Plug USB cable holding "Back" button
    Connected to USB3
    You can now release the keys and allow the process to run. Do not disconnect the phone
    Device identification...OK
    Chip:MSM7227 Model:E15i IMEI:35678504-012722-3 AID:0001 Color:RED
    DEVICE_ID: 86445C8FDFB3D6E39052F50363B0549CE002C3CC
    EROM: 1229-3593 R8A029
    Uploading logic MSM7227:
    Sending LoaderLIVE...OK
    Detecting flash type...OK
    ID: 20BC (ST)
    Chip: ST 4096 Mbit NAND (large page)
    Logical address: 0x08000000
    Size: 528 Mb
    OTP: LOCKED
    Reading TA security data...OK
    Opening TA...OK
    Reading SIMLock data...OK
    Original HwConf certificate detected
    Processing SIMLock signature...OK
    Opening TA...OK
    Writing SIMLock data...OK
    Disconnect USB cable, power on the phone and boot Android OS
    Enable USB Debug in Applications menu, make sure ADB drivers installed. Connect USB cable
    Starting ADB server...OK
    Waiting for BX902ADTB2...OK
    Disabling security...OK
    Waiting for BX902ADTB2...OK
    Removing NAND restrictions...OK
    Waiting for BX902ADTB2...OK
    Disabling security...OK
    Waiting for BX902ADTB2...OK
    Installing required module...OK
    Writing S1boot image...OK
    Rebooting device...OK
    Operation completed successfully. You can disconnect the phone now
    FINISHED [117sec]

  3. #13
    Top Contributor
    Join Date
    Oct 2010
    Location
    BD
    Posts
    2,720
    Thanks
    2
    Thanked 66 Times in 49 Posts

    answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

    LT 15 arc unlock successfully

  4. #14
    Top Contributor
    Join Date
    Oct 2010
    Location
    BD
    Posts
    2,720
    Thanks
    2
    Thanked 66 Times in 49 Posts

    answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

    4SE - tool 1.8.2
    Selected model: K790
    Selected operation: Read info
    Selected interface: UART (BOOTROM)
    Remove battery, wait a few seconds and insert it back
    Connect cable and press "Power" button shortly
    Connected to COM8
    You can now release the keys and allow the process to run. Do not disconnect the phone
    Device identification...OK
    Sending Preloader...OK
    Starting GDFS service...OK
    Reading GDFS security data...OK
    ChipB2020 Model:K790i IMEI:35220601-349505-3 CID:49 Domain:RED
    OTP LOCKED:1 CID:49 PAF:1
    Uploading logic DB2020:
    Firmware details:
    Software Id: R1CG001 prgCXC1250477_GENERIC_EV
    Software revision: R1CG001
    FS Id: cxc1250491
    FS version: R1CG001
    Language Id: S_ASIA_LEVAN
    CDA Id: CDA102568/110
    CDA version: R4A
    Detecting flash type...OK
    ID: 2019 (ST)
    Chip: ST Sibley 512 Mbit NOR
    Logical address: 0x44000000
    Size: 64 Mb
    Supported operations:
    Flash, Unlock, Recovery, Change certificate, GDFS, Dump flash
    Shutting down device...OK
    Operation completed successfully. You can disconnect the phone now
    FINISHED [9sec]

  5. #15
    Top Contributor
    Join Date
    Oct 2010
    Location
    BD
    Posts
    2,720
    Thanks
    2
    Thanked 66 Times in 49 Posts

    answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

    4SE - tool 1.8.2
    Selected model: K790
    Selected operation: Unlock
    Selected interface: UART (BOOTROM)
    Remove battery, wait a few seconds and insert it back
    Connect cable and press "Power" button shortly
    Connected to COM8
    You can now release the keys and allow the process to run. Do not disconnect the phone
    Device identification...OK
    Sending Preloader...OK
    Starting GDFS service...OK
    Reading GDFS security data...OK
    ChipB2020 Model:K790i IMEI:35220601-349505-3 CID:49 Domain:RED
    OTP LOCKED:1 CID:49 PAF:1
    Uploading logic DB2020:
    Detecting flash type...OK
    ID: 2019 (ST)
    Chip: ST Sibley 512 Mbit NOR
    Logical address: 0x44000000
    Size: 64 Mb
    Shutting down device...OK
    Remove battery, wait a few seconds and insert it back
    Connect cable and press "Power" button shortly
    Connected to COM8
    You can now release the keys and allow the process to run. Do not disconnect the phone
    Device identification...OK
    Uploading logic DB2020:
    Sending ResetLoader...OK
    Authenticating with key KIDP96202033...OK
    Reseting to factory defaults...OK
    Shutting down device...OK
    Remove battery, wait a few seconds and insert it back
    Connect cable and press "Power" button shortly
    Connected to COM8
    You can now release the keys and allow the process to run. Do not disconnect the phone
    Device identification...OK
    Uploading logic DB2020:
    Sending ProductionLoader...OK
    Writing EROM...OK
    Writing SIMLock data...OK
    Changing certificate to A1_DB2020_49_RED...OK
    Shutting down device...OK
    Operation completed successfully. You can disconnect the phone now
    FINISHED [27sec]

  6. #16
    Top Contributor
    Join Date
    Oct 2010
    Location
    BD
    Posts
    2,720
    Thanks
    2
    Thanked 66 Times in 49 Posts

    answer: Successfuly Unlocked/Flashed/Repaired phones by 4SE dongle

    4SE - tool 1.8.2
    Selected model: T715
    Selected operation: Unlock
    Selected interface: USB (BOOTROM)
    Checking USB driver status...OK (SEMC Flash Device v2.2.0.5 | 2-22-2011)
    Remove battery, wait a few seconds and insert it back
    Plug USB cable holding both "2" and "5" buttons
    Connected to USB3
    You can now release the keys and allow the process to run. Do not disconnect the phone
    Device identification...OK
    Sending Preloader...OK
    Sending IDloader...OK
    ChipB3210 Model:T715 IMEI:35662703-135114-1 CID:53 Domain:RED
    OTP LOCKED:1 CID:53 PAF:1
    Uploading logic DB3210:
    Detecting flash type...OK
    ID: 2CAA (Micron)
    Chip: Micron 2048 Mbit NAND (large page) x08
    Logical address: 0x80000000
    Size: 264 Mb
    Reading TA security data...OK
    Sending CSLoader...OK
    Authenticating with key KIDP96_EMP_DUMP_R1A...OK
    Reading unique device key...OK
    Device key:9C4A79BD1B3A46BBB34497BDC5A72DB0
    Restarting device...OK
    Connected to USB3
    Device identification...OK
    Sending Preloader...OK
    Sending ResetLoader...OK
    Authenticating with key KIDP96321035...OK
    Reseting to factory defaults...OK
    Restarting device...OK
    Connected to USB3
    Device identification...OK
    Sending Preloader...OK
    Sending ProductionLoader...OK
    Writing SEMCBOOT...OK
    Changing certificate to RED...OK
    Recompiling security area...OK
    Shutting down device...OK
    Operation completed successfully. You can disconnect the phone now
    FINISHED [26sec]

Page 2 of 2 FirstFirst 12

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •