Ford 5000 / 6000 in LOCK13 supported by RCD or RCD PRO - Dhaka Mobile  
Dhaka Mobile

Go Back   Dhaka Mobile > News Section > GSM News & Updates
GSM News & Updates Solution Authors To Announce Releasing Their Updates. No advertise messages here
Forums by Category
Thread Tools Search this Thread Display Modes
Old 11-16-2010, 09:21   #1
Product Supporter
Join Date: Oct 2010
Posts: 581
Status: Offline
Thanks: 0
Thanked 6 Times in 5 Posts
Rep Power: 7
Helpful-Man is on a distinguished road

Ford 5000 / 6000 in LOCK13 supported by RCD or RCD PRO

Martech Team presents next version of LOCK13 Tools, this time for Ford 5000 / 6000 / 7000.
Application works on Martech Clip with RCD or RCD PRO activation.

LOCK10/13 for radios based on MC68HC11PA8

Hardware required:
- Martech CLIP with RCD or RCD PRO activation
- Wires for making connection from cpu test points
- 12V Power Supply

Radios based on this CPU can be repaired via following ways:
- by connecting to CPU testpoints on radio pcb
- by connecting to service connector which is placed on the rear wall of the radio

Due to the stability and effectiveness of combination we suggest a connection to the TXD / RXD signals, located directly on the motherboard.
Test points are located underneath the radio and on the other side - near the main processor unit.

CLIP we connect directly to the radio, using three cables to the points located on the underside of the radio, according to the scheme:

- Clip PORT1.4> TXD - test point, shown at left
- Clip PORT1.5> RXD - test point, shown at right
- Clip PORT 1.7> GND - left side of capacitor

In the event that the board had other pinout, in general it should be connected as follows:
- Clip PORT1.4> TXD PIN1 of radio processor
- Clip PORT1.5> RXD PIN64 of radio processor

Example of connection of the CPU side:

The second way the servicing of these models is the connection to the test pins on the connector, located between the power connector and the speaker connector.

Please connect directly to the radio CLIP with three wires, according to the scheme:

- Clip PORT1.4 > TXD fifth pin connector (from top)
- Clip PORT1.5 > RXD sixth pin connector (from top)
- Clip PORT1.7 > GND (eg at the GND pin power connector)

Check example video :
[Only registered and activated users can see links. ]

Download it:
[Only registered and activated users can see links. ]

  Reply With Quote
Collapse Related threads at Dhaka Mobile
Thread Thread Starter Forum Replies Last Post
Congratulate to 'M.Irfan' to completed 6000+ posts ...:::nerobdms:::... Forum Announcements 11 08-07-2013 12:24
Congratulate to 'M.Irfan' to completed 5000+ posts ...:::nerobdms:::... Forum Announcements 9 06-22-2013 03:09
Lock13 on Ford radios with PIC16F876A - RCD AMS V M.Irfan GSM News & Updates 0 06-16-2013 22:16
ORT-JTAG - MSM 6000 CDMA Support , Huawei U1310 Repair Dead Boot and MORE Ripon_Manikganj GSM News & Updates 0 04-14-2011 06:10
*Congratulation to DHAKA MOBILE 5000+ Members ...:::nerobdms:::... Forum Announcements 10 11-22-2010 12:29


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Clear Default Style - Mobile Style Clear
All times are GMT +1. The time now is 17:51.

Follow us below -

Copyright ©2010-2017. Dhaka Mobile
Registered trademark of vBulletin Solutions