Dhaka Mobile

Go Back   Dhaka Mobile > News Section > GSM News & Updates
GSM News & Updates Solution Authors To Announce Releasing Their Updates. No advertise messages here
Forums by Category
Reply
 
Thread Tools Search this Thread Display Modes
Old 10-05-2010, 15:18   #1
anowar_virus
Senior Member
 
Join Date: Aug 2010
Posts: 403
Status: Offline
Thanks: 3
Thanked 0 Times in 0 Posts
Rep Power: 7
anowar_virus is on a distinguished road
Send a message via Yahoo to anowar_virus

RIFF JTAG - JTAG Manager v1.15, RIFF Box firmware v1.14 released


[Only registered and activated users can see links. ]

Whats new:

Firmware 1.14
---------------------
- code is optimized to avoid deadlocks in Cortex-A8 handling routines (deadlocks appear due to communication errors);
- Cortex-A8 debug is now available in ARM/Thumb modes (use the GDBServer for this);
- ARM946E core support is added (which is mostly a debug access to the CP15 coprocessor);
- added new RESET type for ARM9xxx cores: HW_RESET - targets which have dedicated TRST can be halted
at the very first instruction core executes after the system reset signal (NRST) was applied.
Importance of this: if some harmfull/"unlucky" code is written to a boot zone of a device, which (code)
on the device startup results in h/w blocking, jtag disabling, core resetting, etc., then connecting via JTAG to such target
becomes an impossible task, since JTAG host has not enough time to halt the target before it becomes unusable by a harmfull code.
Using HW_RESET type ensures the target's core does not execute even a single instruction after the reset signal (NRST) was applied.
- removed bug which could cause deadlocks of box during a h/w script execution.
____________
JTAG Manager 1.15
---------------------
- added extended flash chip info handling for example for NOR memories support by DCC Loaders;
- added Resume feature for interrupted writes (which could be performed by WriteMemory button (DCC Page) or by Resurrector DLL):
if target loses power, connection is broken or any other malfuntion happens during write operation, software will store current
write context; you can reconnect target and start write/resurrection again - software will prompt you whether to start again or to continue write from the
interrupted point. This feature is applicable to all write conditions (writes by resurrectors, or manual writes through the DCC Read/Write page features).
- added 3 buttons on Box Service page for quick access to the RIFF's manual PDFs;
- fixed a not harmfull bug inside of the core reset (when NRST is applied) command sequence;
- added feature: if write error appears and 'Ignore' is choosen, user can order software to apply 'Ignore' for further write errors automatically;
- added standalone setup dialog for automatic write errors handling;
- added BAD Blocks Handling feature using the following algo:
If there are data chunks A B C & D to be written into blocks 1 2 3 & 4 respectively, and for example block 3 is found to be BAD, then software will write:
data A -> into block 1
data B -> into block 2
--------> block 3 is bypassed (and marked as bad)
data C -> into block 4
data D -> into block 5
It's clear that block 5 was not intended to accept the data D. Thus:
- if block 5 had some other info then this info will be lost and will be overwritten with the data D.
- if block 5 was free for use, then nothing bad happens.

So, main conclusions:
---------------------
1. BAD Blocks Handling is IMPOSSIBLE (POINTLESS) for writting FULL images (user can chose only 'Ignore' option)
2. When writting data chunks of length less than full flash size user is prompted to select 2 options:
a) Overlap (in example above this would mean to write data D into block 5)
b) Cut Excess (in example above this would mean to not touch original 5th block's contents and just discard data D to be written)

************************************************** ************************************************** *********************************
NOTE: Bad block handling is allowed by default only through the DCC Read/Write page write.
----- Old Resurrector DLLs were not adapted for this feature, thus Bad Block handling will be implemented only in new DLLs.
If you meet a Bad Block Error during resurrection contact support in order to update DLL to a Bad Blocks adapted version.
************************************************** ************************************************** *********************************

- solved problem which caused update module to display files for download which were already up-to-date for cases
when JTAG Manager was installed on FAT (FAT/FAT32) file systems.
- very dangerous bug fixed: "Irnored" word misspelling is corrected to the valid "Ignored" one

  Reply With Quote
Collapse Related threads at Dhaka Mobile
Thread Thread Starter Forum Replies Last Post
RIFF-JTAG--RIFFJTAG Manager v1.50 released M.Irfan GSM News & Updates 0 08-03-2013 08:46
RIFF JTAG - JTAG Manager Version 1.38, RIFF Box Firmware v1.29, Tegra 2 Support ! ! maninder_111 GSM News & Updates 0 12-28-2011 09:01
RIFF JTAG – JTAG Manager v1.20, RIFF Box firmware v1.16 released M.Irfan RIFFBOX 0 12-16-2010 18:39
RIFF JTAG – JTAG Manager v1.20, RIFF Box firmware v1.16 released M.Irfan GSM News & Updates 0 12-16-2010 18:34
RIFF Box JTAG Manager Version 1.17- JTAG Pins Detection added, WORLD FIRST M.Irfan GSM News & Updates 0 10-14-2010 15:02

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes


Resource
Service
Company
Clear Default Style - Mobile Style Clear
All times are GMT +1. The time now is 09:38.
Clear

Follow us below -

Copyright ©2010-2016. Dhaka Mobile
Registered trademark of vBulletin Solutions
An DHAKA MOBILE Company