Thread: Successfully unlocked/repaired phones by Infinity-Box

Page 1 of 5 1234 ... Last»
Reply to Thread
  1. #1
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    Successfully unlocked/repaired phones by Infinity-Box


    Fly SX 200 Unlock done here is log ,

    COM17 [VCP1] selected
    Action: unlock
    unlock method: smart fast
    Model: Fly-SX200
    Checking data, wait...
    Phone should be Switched OFF !
    Press and HOLD Power button now !
    19200 autodetect
    Initializing[6225:8A03:8A00]...
    CPU: MT6225
    chip: 0001:9D03:0001
    Connecting, wait...
    Release Power button now !
    Phone detected, wait...
    Hardware: MT6225,E03
    Date: 2006.06.14
    Version: 1.0
    Version: MAUI.07A.W07.36.MP.V23
    Version: EZIO25_07A_HW
    44 byte(s) read
    imei: 35342302016731
    connection Ok
    157 byte(s) read
    reading data...
    building new data...
    writing data...
    145 byte(s) read
    reading data...
    building new data...
    writing data...
    verifying...
    verification Ok
    done
    Finished, time used: 9 sec
    Remove/Install battery now !

  2. #2
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    toshiba TS10 unlocked with pin-out i want to share this to all...

    toshiba unlocking...using my infinity box...

    heres the pin out...



  3. #3
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    Sucesfully Unlocked Benq S660C RIPCURL with Infinity Box The only difficult step was make the cable. Maybe the TXT in the Infinity Box Shell is not too easy to undersatand. But the cable is very simple. Changing the pinout of Motorola T190 Cable.
    The Unlock Process?????? Very easy, Infinity always work!!!!!!!!!!!!

    Here is the Log:

    COM5 [VCP0] selected
    modulo v1.31
    Device: BenQ-S660C
    Checkeando datos, espere...
    Action: unlock
    Boot...
    El Telefono deberia estar APAGADO !
    Presiona boton POWER Ahora !
    Connecting...
    Boot Done
    Check Connection...
    Check Connection Done
    Set Baud...
    812500
    Set Baud Done
    Check Flash...
    error: Probably wrong model selected.
    Continue anyway ?
    Check Flash Done
    Check Parameters...
    Flash: 0089:88C500010001
    Archivo guardado: C:\Archivos de

    programa\InfinityBox\BModule\eeprom-00_20090325-021655.78F.bin
    Archivo guardado: C:\Archivos de

    programa\InfinityBox\BModule\eeprom-01_20090325-021659.78F.bin
    Archivo guardado: C:\Archivos de

    programa\InfinityBox\BModule\eeprom-02_20090325-021703.78F.bin
    Check Parameters Done
    Check Space...
    Flash: 0089:88C500010001
    flash: Intel I28F320C3B-B B 4Mb
    Check Space Done
    Check Data...
    Check Data Done
    Erasing...
    erase operation not required
    Erasing Done
    Writing...
    Flash: 0089:88C500010001
    Flash: 0089:88C500010001
    Flash: 0089:88C500010001
    Writing Done
    Finished, time used: 35 sec
    Quite/coloque la bateria ahora !


    THANKS INFINITY, the solution when other tool nothing have to do.

  4. #4
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    Emblaze-Touch7 Unlock again ==== log opened: [4/1/2009 3:08:58 AM] ====
    Application: C:\Program Files\InfinityBox\MModule\MModule.exe
    Loading data, wait...
    [Infinity Box] v2.69
    S/N: xxx:0112
    Wait...
    Device: Emblaze-Touch7
    Done
    ==== log: [4/1/2009 3:09:25 AM] ====
    COM6 [VCP0] selected
    module v2.69
    Action: read codes
    unlock method: read codes
    Model: Emblaze-Touch7
    Checking data, wait...
    Phone should be Switched OFF !
    Press and HOLD Power button now !
    19200 autodetect
    Initializing [6219:8B02:8B01]...
    CPU: MT6219
    chip: 0031:FB41:0BFC
    status: FF
    detected CPU: MT6226MA
    Connecting at 19200, wait...
    Release Power button now !
    Phone detected, wait...
    Hardware: MT6219B,E02
    Date: 2005.04.12
    Version: 1.0
    Version: SL900A.05C.W06.08.MP.V64
    Version: ESL6227_05C_HW
    60 byte(s) read
    imei: 35385801025518
    connection Ok
    208 byte(s) read
    Phone lock: Off
    Network lock: On
    Network subset lock: Off
    Service provider lock: On
    Corporate lock: Off
    IMSI lock: Off
    Auto lock: Off
    NP code: 32534669/23356496
    locked to: FFF-FF
    SP code: 0000000000003344/0000000000003344
    CP code: FFFFFFFFFFFF0000/FFFFFFFFFFFF0000
    IMSI code: 1010087726693132/0101807762961323
    Phone code: 3343FFFFFFFF1000
    Finished, time used: 13 sec
    Remove/Install battery now !

  5. #5
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    Alcatel OT-701 UNLOCK 100% ok i am useing this version

    C701X-2ARGFR1_XC18SB20_JRD26_06A_PCB01_GPRS_MT6226_S02.M AUI_06A_W06_52_SP1_V17_2007-10-22_simfree_En_Fr_Es_It_De.B0M
    then complete format phone 100 % ok

    module v2.70
    Device: Alcatel-C701X, C701A
    Checking data, wait...
    advanced flash detection enabled
    Action: "format ffs"
    Boot ...
    Press and HOLD Power button now !
    19200 fixed
    Connecting, wait...
    Initializing [6226:8A03:8A02]...
    CPU: MT6226
    chip: 0031:0576:A000
    status: 01
    boot packet size: 0400
    Release Power button now !
    Boot Done
    Initialize ...
    detecting chip #00 in region #00...
    flash: 01227E22302200:2BEA0000000000
    flash: Amd AMD/Fujitsu std [D 0004x008000 00FEx020000 0004x008000] 32Mb
    number of flash chip/regions detected: 01/01
    Initialize Done
    Set baud ...
    921600
    Set baud Done
    Initialize bootcode ...
    Initialize bootcode Done
    Check firmware integrity ...
    detect device identification#1...
    detection phase #1...
    detect device identification#1 finished
    identification#1 structure: 2nd [enhanced] generation
    security area (code #1) is Ok
    security area (code #1) backup saved: C:\Program Files\InfinityBox\MModule\backup_security\id.0C828 86B.[JRD26_06A_PCB01_GPRS_MT6226_S02.MAUI_06A_W06_52_SP 1_V17.BIN_6DAFF008].rpl
    identification#1 detection finished
    device-id: 0C82886B
    identification#1 protocol ver: 05
    ver. sw 1: JRD26_06A_PCB01_GPRS_MT6226_S02.MAUI_06A_W06_52_SP 1_V17.BIN
    ver. sw 2: MAUI.06A.W06.52.SP1.V17, F70F5092
    ffs offset/size: 01200000/00E00000
    detect device identification#2...
    detection phase #1...
    detect device identification#2 finished
    sim-lock status: disabled
    Check firmware integrity Done
    Check firmware content ...
    Check firmware content Done
    Backup required data ...
    original imei: 35320501055562
    flash: 01227E22302200:2BEA0000000000
    Backup required data Done
    Patch required data ...
    Patch required data Done
    Special operation ...
    Special operation Done
    Write ...
    Write Done
    Finalization ...
    formatting...
    flash: 01227E22302200:2BEA0000000000
    Finalization Done
    file saved: C:\Program Files\InfinityBox\MModule\backup_security\Alcatel-C701X,C701A_JRD26_06A_PCB01_GPRS_MT6226_S02.MAUI_0 6A_W06_52_SP1_V17__system_log_0C82886B_6DAFF008_20 090421-011851.B0X.bin
    Finished, time used: 175 sec
    Remove/Install battery now !

    File system has been modified !
    It is need to press and HOLD phone "Power" button
    during long time (up to 1 min) to make phone Powered-On !

    thanks for infinity team

  6. #6
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    x761 unlock ok COM8 [VCP0] selected
    module v2.68
    Action: unlock
    unlock method: smart fast
    Model: ZTE-X761
    Checking data, wait...
    Phone should be Switched OFF !
    Press and HOLD Power button now !
    19200 autodetect
    Initializing [6225:8A03:8A00]...
    CPU: MT6225
    chip: 0001:BF03:0001
    status: FF
    Connecting at 19200, wait...
    Release Power button now !
    Phone detected, wait...
    Hardware: MT6225,E03
    Date: 2006.06.14
    Version: 1.0
    Version: X761_Z0_S_A07A103
    Version: ZTEMT25_07A_HW_A
    44 byte(s) read
    imei: 357873020xxxxx
    connection Ok
    157 byte(s) read
    reading data...
    reading data #4...
    building new data...
    writing data...
    145 byte(s) read
    reading data...
    building new data...
    writing data...
    verifying...
    verification Ok
    done
    Finished, time used: 15 sec
    Remove/Install battery now !

  7. #7
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    kp260 full imei and unlock by infinity box....process by WILUNLOCK



    LOG OPERACION


    Phone must be SWITCHED ON !
    Connecting, wait...
    Connection Ok
    Action: imei
    software version: KP260dAT-00-V10a-732-101-JUL-30-2008+2
    original imei: 00000000000000000
    new imei: 01295162284355
    imei verification Ok
    Done
    Finished

  8. #8
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    ZTE i766


    imei repair full


    Action: imei
    Model: Autodetect 6205-6227 NOR
    Checking data, wait...
    Phone should be Switched ON !
    Connecting, wait...
    Phone detected, wait...
    Hardware version: MT6225, E03
    Hardware version: ZTEMT25_07A_HW_A
    Software version: I766_V2_Z1_S_A0FA108
    Software date: 2006.06.14
    Barcode: 50010811229148854567500833220409 101
    imei: 357963010565925
    imei write method: mode-1
    imei write channel: imei #1 for dual sim/mono CPU
    new imei: 0129216219xxxxxx
    verification Ok
    Finished, time used: 5 sec
    Power off phone now !

  9. #9
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    LOG OPERATION ..IMEI FULL ME550 FULL WITH INFINITY BOX


    Phone must be SWITCHED ON !
    Conectando, espere...
    coneccion Ok
    Action: imei
    version de software: ME550dP64FL-57-V10a-732-101 Aug 17 2007+6
    Imei original: 01121600318498200
    Nuevo imei: 01220462550745
    imei verification Ok
    Listo
    Finished

  10. #10
    Top Contributor ranksranksranksranksranksranksranksranks
    Join Date: Oct 2010 Location: BD Member: 507 Status: Offline Posts: 2,719
    Thanks Meter: 64

    answer: Successfully unlocked/repaired phones by Infinity-Box

    COM7 [VCP0] selected
    module v1.65
    Device: Sagem-my220x
    Checking data, wait...
    Action: unlock
    unlock method-1
    Boot ...
    Press and HOLD Power button now !
    e-gold: 820010
    loading...
    middle part...
    next part...
    boot answer: 01
    Release Power button now
    Boot Done
    Set Baud ...
    230400
    Set Baud Done
    Connecting ...
    flash: 0001:011A
    Connecting Done
    Check hardware ...
    Check hardware Done
    Check parameters ...
    Check parameters Done
    backup critical area ...
    reading eeprom-static...
    file saved: C:\Program Files\InfinityBox\Pana01\Sagem-my220x_eeprom-static_20090331-134914.B1E.bin
    loading data...
    data loaded
    reading eeprom-security...
    file saved: C:\Program Files\InfinityBox\Pana01\Sagem-my220x_eeprom-security_20090331-134914.B1E.bin
    reading eeprom-complete...
    file saved: C:\Program Files\InfinityBox\Pana01\Sagem-my220x_eeprom-complete_20090331-134917.B1E.bin
    reading additional data...
    file saved: C:\Program Files\InfinityBox\Pana01\Sagem-my220x_lock-area_20090331-134931.B1E.bin
    backup critical area Done
    Check memory ...
    lock found
    Check memory Done
    Write ...
    Erasing: lock-area
    Writing: lock-area
    Write Done
    Finished, time used: 104 sec
    Remove/Install battery now !

Reply to Thread
Page 1 of 5 1234 ... Last»
Share with